Chemical injection mortar Basic WIT-PM 200
Chemical injection mortar Basic WIT-PM 200
ANC-MORT-(WIT-PM200)-CART-420ML
Register now and access more than 125,000 products
Two-part reactive resin mortar, styrene-free polyester
Individual fixing point in uncracked concrete:
Anchor rod W-VI-A, anchor rod W-VD-A, standard threaded rod with acceptance test certificate 3.1
Individual fixing point in masonry (system with perforated sleeve SH):
Anchor rod W-VI-A, standard threaded rod with acceptance test certificate 3.1, perforated sleeve SH
- European Technical Assessment ETA-12/0569: Individual fixing point + uncracked concrete (anchor rod W-VI-A, anchor rod W-VD-A, standard threaded rod with acceptance certificate 3.1)
- European Technical Assessment ETA-13/0037: Individual fixing point + masonry (anchor rod W-VI-A, standard threaded rod 3.1, perforated sleeve SH, aerated concrete only without perforated sleeve)
Wall units
Wooden structures
Stairs
Drill holes with a rotary drill (without impact mechanism)
Clean drill hole; 2x blow out/2x brush out/2x blow out
Cut anchor rod to length and mark the desired insertion depths
Insert sieve bush
Screw mixer onto cartridge
Before use, press out approx. 10 cm cord
Completely fill with composite mortar from end of perforated sleeve
Press in anchor rod up to the bottom of the sleeve while turning slightly
Comply with hardening time of composite mortar
Install component, max. torque must not be exceeded
Create the drill hole
Clean drill hole; 2x blow out/2x brush out/2x blow out
Cut anchor rod to length and mark the desired insertion depths
Screw mixer onto cartridge
Before use, press out approx. 10 cm cord
Fill with composite mortar starting from drill hole base (see enclosed leaflet)
Press in anchor rod up to the bottom of the sleeve while turning slightly
Visual check of mortar volume, embedment depth mark
Comply with hardening time of composite mortar
Install component, max. torque must not be exceeded
Create the drill hole
Clean drill hole; 2x blow out/2x brush out/2x blow out
Cut anchor rod to length and mark the desired insertion depths
Screw mixer onto cartridge
Before use, press out approx. 10 cm cord
Fill composite mortar from bottom of drill hole
Press in anchoring element up to drill hole base while turning slightly
Visual check of mortar filling quantity, setting depth marking
Comply with hardening time of composite mortar
Install component, apply installation torque
- European Technical Assessment ETA-12/0569: Individual fixing point + uncracked concrete (anchor rod W-VI-A, anchor rod W-VD-A, standard threaded rod with acceptance certificate 3.1)
- European Technical Assessment ETA-13/0037: Individual fixing point + masonry (anchor rod W-VI-A, standard threaded rod 3.1, perforated sleeve SH, aerated concrete only without perforated sleeve)
Datasheets(X)
- Attachment in uncracked concrete, solid and perforated brick masonry, aerated concrete
- Suitable for attaching wooden structures, metal structures, metal profiles, brackets, grilles, sanitary ware, pipes, cable conduits, etc.
Contents | 420 ml |
Temperature resistance, long-term temperatures max. | 50 °C |
Temperature resistance, short-term temperatures max. | 80 °C |
Shelf life from production/conditions | 18 Month / at 5°C to 25°C |
Chemical basis | Polyester, styrene free |
Colour | Concrete grey |
Last viewed
Clay series cleaning pad
Polishing pads
ORSY® 100 stacking cabinet ORSY® 100
Connector DIN 7427 1/4 inch
7-pin connector 12 V
Hexagonal nut, low profile
Screwdriver with 1/4 inch tip with square drive at the end of the handle
Allen key
Metric combination wrench with POWERDRIV®
Locking nut DIN 7967 hot-dip galvanised steel