Quick-action ceiling anchor W-DS/S With hooks
Quick ceiling anchor W-DS/S
ANC-(W-DS/S)-(A2K)-6X75
Register now and access more than 125,000 products
- Quick and easy to install
- Less drilling effort
- No special drill or setting tool required
- Simple insertion process: Insert by hand, pull down sharply – done
- Anchorage via friction locking – controlled expansion anchor
Multiple attachment of non-load-bearing systems in concrete: European Technical Approval ETA-13/0490
- Dimensioning in accordance with the “Guideline for European Technical Approval (ETAG) for metal anchors in concrete” Appendix C, Dimensioning method C
- The anchor has European Technical Approval for use in reinforced or non-reinforced standard concrete with a strength class of min. C20/25 and max. C50/60 in accordance with EN 206-1:2000-12.
- Multiple attachment of non-load-bearing systems; Anchorage with European Technical Approval in cracked concrete (tension zone) and non-cracked concrete (compression zone)
Create the drill hole
Clean the drill hole
INSERT W-DS/S.
Fully insert W-DS/S.
Pull down the W-DS/S with a jerky movement.
Multiple attachment of non-load-bearing systems in concrete: European Technical Approval ETA-13/0490
- Dimensioning in accordance with the “Guideline for European Technical Approval (ETAG) for metal anchors in concrete” Appendix C, Dimensioning method C
- The anchor has European Technical Approval for use in reinforced or non-reinforced standard concrete with a strength class of min. C20/25 and max. C50/60 in accordance with EN 206-1:2000-12.
- Multiple attachment of non-load-bearing systems; Anchorage with European Technical Approval in cracked concrete (tension zone) and non-cracked concrete (compression zone)
Datasheets(X)
- Suitable for attaching: Lightweight ceiling coverings and false ceilings, ceiling substructures with wire hook, wire hanger, Vernier hangers, light strips, luminaire carrier rails, lamps, cables, chains etc.
- The anchor can be used only in dry indoor areas
| Performance data | ||
| Anchor diameter [mm] | 6 | |
| Anchors in a redundant non-structural system in non-load-bearing systems in concrete (for all load directions) | Fadm [kN] ≥ C20/25 and ≤ C50/601) | 0,5 |
| Würth system components (see 33.1 W-DN) 1) The partial safety factors of the resistances regulated in the approval and a partial safety factor of the actions of γF = 1.4 have been taken into account. Please refer to the European Technical Approval Guidelines (ETAG), Annex C, for information on combining tensile and transverse loads, influence of the edge distance and groups of anchors. | ||
| Characteristic values | ||
| Minimum spacing | smin [mm] | 200 |
| Minimum edge distance | cmin [mm] | 100 |
| Minimum member thickness | hmin [mm] | 80 |
| Effective anchorage depth | hef [mm] | 33 |
| Nominal drill diameter 2) | d0 [mm] | 6 |
| Diameter of cutting edges2) | dcut ≤ [mm] | 6,4 |
| Drill hole depth | h1 ≥ [mm] | 40 |
| Würth system components (see 33.1 W-DN) 2) Tungsten carbide hammer drill bits must comply with the specifications set out in the information leaflet of the Deutsches Institut für Bautechnik (German Institute of Civil Engineering - DIBt) and the Association of German Tool Manufacturers (FWI) on the "characteristic values, requirements and tests for masonry drill bits with tungsten carbide cutting body which are used for making drill holes for anchoring". Würth hammer drill bits meet the specifications set out in the information leaflet. | ||
Last viewed
Combi screw tap assortment Bit HSS SMART STEP, 6 pieces
Hydraulic manual crimping pliers B12 for wire cable terminals in cases, without crimping jaws
Pin punch In accordance with DIN 6450 form C with hardened impact head
1/2 inch impact socket wrench insert DIN 3121/ISO 1174
Hexagonal bolt with shank DIN 931, steel 10.9, plain
System insert, plastic, 4.4.1
Combination wrench assortment, inch Short design, 8 pcs
Screwdriver slotted striking cap with hexagon shank
Suction clamp assortment
Male thread plug-in nipple